The 125W Class D subwoofer power amplifier circuit designed with the LM4651 and LM4652 is shown in the figure. The amplifier has an output power of 125W at total harmonic distortion THD=1%, a load impedance of RL=4Ω, a maximum level of input signal Vin(rms) of 3V, an input signal bandwidth of 10 to 150 Hz, and an ambient temperature of 50 °C. The power supply voltage is ±20V.
The LM4651 in a 28-pin DIP package is a PWM control/driver IC with built-in oscillator, PWM comparator, error amplifier, feedback amplifier, level shifting and high-side drivers, low-side drivers and undervoltage, overtemperature, short-circuit and overmodulation protection circuits . The LM4652 is a half-bridge power MOSFET IC in a TO-220 package with 15 pins (6, 8, 9, {11}, {12} pins not connected). The breakdown voltage of the four MOSFETs is V(BR)DSS=50V. The drain current ID = 10A, the on-state resistance RDS(ON) = 200mΩ (typ.), and the turn-on voltage VGS(th) = 0.85V (typ.).
The oscillator frequency fosc = 1 x 109 / (4000 + Rosc) in the LM4651, where Rosc = R6 = 3.9 kΩ, then fosc = 125 kHz. The input audio signal is input to the error amplifier with a gain of 7î€5V/V (ie, 17î€5dB) via C1, R1, and 10 pins. The half-bridge switch output on the IC27 pin and the {15} pin is filtered by the RC filter and fed back to the {14} pin of IC1. The {19} pin is outputted by the internal feedback measuring amplifier and then the pin 10 is output from pin 9 to provide the error amplifier. A single-ended feedback signal. The audio input signal is compared to the triangular wave generated by the oscillator, and a square wave pulse having a duty factor proportional to the input audio signal level is generated at the output of the PWM comparator to drive the power MOSFET in IC2. The switching output of IC27 pin and {15} pin is low-pass filtered by L1, C16 and L2, C17 to drive the speaker.
The resistor R4 on the IC1{18} pin is used as a short-circuit current limit. When R4=100kΩ, the short-circuit current level is not lower than 10A; the resistor R5 on the {17} pin is used to set the dead time; the capacitor C9 on the {24} pin is used to set the start delay time (1 second) When the {13} pin (STOBY) is placed at logic "1" or 5V, the standby function is executed, the pulse width modulation is stopped, and the power switch in the LM4652 is turned off, which consumes only a very low current. As long as the junction temperature of IC2 reaches 150 °C, the output of the 4-pin is fed back to the {12} pin of IC1 to perform the thermal shutdown function. 
This article refers to the address: http://
PSE Solar Cable are the kind of cable specially used for solar power systems. They have the following features and advantages:
1. High weather resistance: PSE solar cable are made of special materials, has excellent weather resistance, can be used for a long time in a variety of harsh outdoor environments, and are not easy to age and break.
2. High temperature tolerance: PSE solar cable can withstand the work in a high temperature environment, and will not cause electrical performance degradation or damage due to temperature rise.
3. High electrical performance: PSE solar cables have the characteristics of low resistance and low voltage drop, which can effectively transmit the electrical energy generated by the solar system and reduce energy loss.
4. Fire performance: PSE solar cables have made of flame retardant materials, have good fire performance, can effectively prevent the spread of fire in the event of a fire, protect the safety of the solar system.
5. Environmental protection and reliability: PSE solar cables meet environmental protection requirements, do not contain substances harmful to the environment, are safe and reliable, can be used for a long time without causing pollution to the environment.
In short, PSE solar cable iare the high-quality, high-performance cable products, suitable for the installation and operation of various solar power systems. They can provide stable and reliable power transmission, and have the advantages of weather resistance, high temperature resistance, fire resistance and environmental reliability, and are the indispensable part of the construction of solar energy systems.
PSE Solar Cable,Direct Current Cord Cable,Light Voltage Line,PV Solar Cable
Suzhou Yonghao Cable Co.,Ltd. , https://www.yonghaocable.com